Restricted area
DELLAS
Avatar
Restricted area

The page or content you are trying to access is a Members only area.

Reset My password - Remind Me My username

Username
Password
Remember me
Main menu

Milling cutter Disc

LAPITEC® - LAMINAM® - FLORIM - NEOLITH - DEKTON® - SANTA MARGHERITA

TOOL MATERIAL PROCESSING MACHINE
Milling Lapitec® - Laminam® - Florim - Neolith - Dekton® - Santa Margherita Cut - 45° Cut Milling

Standard features

Diameter (mm) Teeth
No. of Segments
Core (mm) Marble Segment dimension
Length x Thickness x Height (mm)
350 25 2.5 for straight cut and 45° tilted cut 44 x 3,0 x 10
400 29 2.5 for straight cut 44 x 3,0 x 10
400 29 3.5 lowered 2.2 for straight cut and 45° tilted cut 44 x 3,0 x 10

Operating Tips

LAPITEC ® (12 mm slab)
LAMINAM® (12 mm slab)
NEOLITH (12 mm slab)
Diameter
(mm)
Revolutions (spindle) Infeed
(mm/min)
Feed
(mm/min)
Outfeed
(mm/min)
350 1600/1800 400/500* 1600/1800* 400/500*
400 1400/1600 400/500* 1400/1600* 400/500*
* for the 45° tilted cut, we recommend reducing the feed by approximately 50%
FLORIM (6 mm slab)
Diameter
(mm)
Revolutions (spindle) Infeed
(mm/min)
Feed
(mm/min)
Outfeed
(mm/min)
350 1600/1800 400/500* 1600/1800* 400/500*
400 1400/1600 400/500* 1400/1600* 400/500*
* for the 45° tilted cut, we recommend reducing the feed by approximately 50%
DEKTON®(20 mm slab)
Diameter
(mm)
Revolutions (spindle) Infeed
(mm/min)
Feed
(mm/min)
Outfeed
(mm/min)
350 1600/1800 300/400* 600/800* 300/400*
400 1400/1600 300/400* 600/800* 300/400*
* for the 45° tilted cut, we recommend reducing the feed by approximately 50%
SANTA MARGHERITA (20 mm slab)
Diameter
(mm)
Revolutions (spindle) Infeed
(mm/min)
Feed
(mm/min)
Outfeed
(mm/min)
350 1600/1800 300/400* 600/800* 300/400*
400 1400/1600 300/400* 600/800* 300/400*
* for the 45° tilted cut, we recommend reducing the feed by approximately 50%

OPERATING PRECAUTIONS

  • While cutting, the disc must come 2 mm out of the material.
  • Use plenty of water while cutting. Spray water towards the front of the disc plate, as close to the cutting area as possible.
  • Make sure the cutting bench is in good condition. Otherwise put a rubber surface between the bench and the material.

MORE INFORMATIONS
The data in this sheet provides useful information, but is not intended to be comprehensive. Contact you retailer or Dellas S.p.A. directly regarding any problems. We would be happy to help you find a solution to your needs. The information contained in the following document is the property of Dellas S.p.A. Its reproduction and transmission is forbidden by law.

Milling cutter Disc

We use cookies to improve our website and your experience when using it. Cookies used for the essential operation of the site have already been set. To find out more about the cookies we use and how to delete them, see our cookies policy.

I accept cookies from this site